rules/make/host: update version/package to fix bug in make.

architectures/cortex-a72.cfg

@@ -1,6 +0,0 @@
-cfg_target_canonical="armv11-$cfg_glued_vendor-linux-gnueabi"
-cfg_target_linux='arm'
-cfg_target_uboot_arch='arm'
-cfg_target_gcc_flags='-O2 -pipe -funit-at-a-time -mcpu=cortex-a72 -mtune=cortex-a72 -mfloat-abi=hard -mfpu=neon-fp-armv8'
-cfg_target_gcc_configure_flags='--with-cpu=cortex-a72 --with-tune=cortex-a72 --with-fpu=neon-fp-armv8 --with-float=hard'
-cfg_target_ar_flags='aarch64-elf'

rules/gcc/common.bash

@@ -5,12 +5,12 @@ version=\
 
 url=\
 (
-    "http://mirrors.kernel.org/gnu/gcc/gcc-$version/gcc-$version.tar.bz2"
+    "https://lsts.pt/glued/gcc-$version.tar.bz2"
 )
 
 md5=\
 (
-    '6f831b4d251872736e8e9cc09746f327'
+    '0abd6a50e1d6cf1642ae2414cc5a10b6'
 )
 
 build_dir=$pkg_var

rules/make/host.bash

@@ -5,12 +5,12 @@ version=\
 
 url=\
 (
-    "http://ftp.gnu.org/gnu/make/make-$version.tar.bz2"
+    "https://lsts.pt/glued/make-$version.tar.bz2"
 )
 
 md5=\
 (
-    '1a11100f3c63fcf5753818e59d63088f'
+    '69520444a44561c8ce10276eee8ec55e'
 )
 
 maintainer=\

rules/ncurses/common.bash

@@ -1,6 +1,6 @@
 version=\
 (
-    "5.9"
+    "6.1"
 )
 
 url=\
@@ -10,7 +10,7 @@ url=\
 
 md5=\
 (
-    "8cb9c412e5f2d96bc6f459aa8c6282a1"
+    "98c889aaf8d23910d2b92d65be2e737a"
 )
 
 maintainer=\

systems/lctr-a72xx/cfg/firmware/config.txt

@@ -1,51 +0,0 @@
-# For more options and information see 
-# http://www.raspberrypi.org/documentation/configuration/config-txt.md
-# Some settings may impact device functionality. See link above for details
-
-kernel=uboot.bin
-device_tree_address=0x02000000
-
-# enable i2c
-dtparam=i2c_arm=on
-dtparam=spi=on
-
-# uncomment if you get no picture on HDMI for a default "safe" mode
-#hdmi_safe=1
-
-# uncomment this if your display has a black border of unused pixels visible
-# and your display can output without overscan
-#disable_overscan=1
-
-# uncomment the following to adjust overscan. Use positive numbers if console
-# goes off screen, and negative if there is too much border
-#overscan_left=16
-#overscan_right=16
-#overscan_top=16
-#overscan_bottom=16
-
-# uncomment to force a console size. By default it will be display's size minus
-# overscan.
-#framebuffer_width=1280
-#framebuffer_height=720
-
-# uncomment if hdmi display is not detected and composite is being output
-#hdmi_force_hotplug=1
-
-# uncomment to force a specific HDMI mode (this will force VGA)
-#hdmi_group=1
-#hdmi_mode=1
-
-# uncomment to force a HDMI mode rather than DVI. This can make audio work in
-# DMT (computer monitor) modes
-#hdmi_drive=2
-
-# uncomment to increase signal to HDMI, if you have interference, blanking, or
-# no display
-#config_hdmi_boost=4
-
-# uncomment for composite PAL
-#sdtv_mode=2
-
-#uncomment to overclock the arm. 700 MHz is the default.
-#arm_freq=800
-

systems/lctr-a72xx/config

@@ -1,19 +0,0 @@
-cfg_architecture='cortex-a72'
-cfg_storage='data0:ext4:/opt'
-cfg_services0='dropbear network storage upgrade syslog ptpd'
-cfg_services1=''
-cfg_services2='dune'
-cfg_modules=''
-cfg_packages='dropbear rsync busybox e2fsprogs dosfstools ptpd rpcbind rpi-boot-firmware bison binutils openssl linux/rpi exiftool libusb'
-cfg_target_linux_kernel='arch/arm/boot/zImage'
-cfg_ptpd_interface='eth0'
-cfg_eth_ext_mk='255.255.0.0'
-cfg_eth_ext_gw='10.0.0.1'
-cfg_terminal='tty1'
-cfg_partitions=\
-(
-    rpi-boot BOOT0  512B    32MiB
-    root     root0  32MiB   544MiB
-    data     data0  544MiB  -1
-)
-

systems/lctr-a72xx/lctr-a72xx-testbed.cfg

@@ -1,3 +0,0 @@
-cfg_hostname="lctr-a72xx-testbed"
-cfg_eth_ext_ip="10.0.200.18"
-cfg_kernel_boot_dev='/dev/mmcblk0p1'